No hot water at all
We test the pilot assembly, thermocouple, heating elements, and breakers to find the exact failure. Most no-hot-water calls are fixed in under two hours with parts we carry on the truck. You get hot water back the same day.
When your water heater quits, you need water heater repair Decatur GA homeowners actually trust. We diagnose gas and electric units, fix leaks, replace failed elements, and restore hot water the same day across Decatur, Georgia. Whether it is a cold shower before work or a tank leaking onto your basement floor, our licensed technicians carry the parts and tools to get it handled in one visit.

Water heater repair in Decatur means finding out why your unit stopped producing hot water or started leaking, then fixing that specific failure instead of selling you a new tank you do not need. We test the heating element or gas burner, check the thermocouple and pilot assembly, inspect the anode rod, and pressure-test the tank and fittings. Common fixes include replacing a burned-out element with a water heater element wrench, swapping a failed thermocouple, clearing sediment from the tank bottom, and resealing inlet and outlet connections with Teflon tape and pipe dope.
Most Decatur homes we service have either a gas tank unit in the garage or a closet-mounted electric heater in a hallway. Both take a beating here. Decatur's older housing stock means original copper pipe and aging supply lines that fail at the same time as the heater. If you have no hot water and it is a gas unit, the pilot light is usually the first thing we check. If you are searching for water heater repair near me Decatur GA on a Sunday night, we answer the phone and roll a truck.
Every repair call includes a full diagnostic, a flat-rate quote before work begins, and a test of the finished job. Here is what is covered when we come out.
We test the heating element or burner, check the thermocouple and pilot, inspect the anode rod, pressure-test the tank and fittings, and verify the T&P valve is working. You get a clear picture of what failed and what is still in good shape.
Before we touch a wrench, you get the exact price for the fix. No hourly billing, no surprise add-ons. If the job needs a part we do not have on the truck, we tell you the cost and the timeline before we order it.
Every repair we do is warrantied on both parts and labor. If the same failure comes back within the warranty window, we return and fix it at no charge. We put the terms in writing so you have it on file.
All repairs meet Uniform Plumbing Code and International Plumbing Code standards. We install T&P valves, expansion tanks, and venting to spec. If your setup was not code-compliant before, we bring it up to standard while we are in there.
We lay drop cloths, haul away old parts, and leave your utility room or closet cleaner than we found it. No solder drips on the floor, no leftover fittings, no mess for you to deal with after we leave.
You call and describe what is happening: no hot water, rusty water, a puddle, a popping sound. We ask three or four questions to narrow it down, give you a ballpark range, and schedule a same-day window. If it is an emergency like an active leak flooding a floor, we move you to the front of the line.
The technician arrives, shuts off the gas or power, and inspects the unit. We check the T&P valve, anode rod, heating elements or burner assembly, flue venting, and all fittings. We use a multimeter on electric units and a manometer on gas units. This takes 15 to 25 minutes.
We tell you what failed, why it failed, and what it costs to fix. You get a flat-rate price before any work starts. If repair does not make sense, we say so and quote a replacement instead. No pressure either way.
Once you approve, we do the work. Element swap, thermocouple, pilot assembly, pressure relief valve, expansion tank, or inlet/outlet fitting repair. Most jobs take 45 to 90 minutes. We use pipe wrench, pipe cutter, soldering torch, and PEX crimping tool as needed, and we test every connection before we button up.
We refill the tank, restore power or gas, and run hot water until it hits temperature, usually 120 to 140 degrees depending on your setting. We check for leaks at every joint, confirm the T&P valve is not weeping, and show you what we did. You get a written summary and our warranty terms before we leave.
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Used to remove and replace screw-in heating elements on electric water heaters without damaging the tank fitting.
Tests continuity and resistance on heating elements, thermostats, and wiring to pinpoint electrical failures fast.
Used to disconnect and replace supply lines, fittings, and nipples on both gas and electric units.
For repairing or replacing copper pipe and PEX tubing connections when inlet or outlet lines need to be reworked.
Traces moisture back to its source when the leak is not obvious, including slab leak symptoms near the heater.
Checks gas pressure at the water heater to confirm the unit is getting the correct supply for safe, efficient operation.
A family in Oakhurst woke up to no hot water on a Saturday. The gas water heater pilot would not stay lit. They had tried relighting it twice with no luck and were ready to buy a new unit.
We replaced the thermocouple and pilot assembly in under an hour. Total cost was $220. The heater fired right up and has been running fine since. They avoided a $1,200 replacement they did not need.
A homeowner in Winnona Park noticed water pooling around the base of their electric heater. They assumed the tank was cracked and were preparing to replace it. The leak had been growing for about a week.
We diagnosed a failed T&P valve, not a cracked tank. Replaced the valve and the expansion tank for $340. The leak stopped immediately and the heater is still in service. They saved over $800 versus replacement.
A North Decatur homeowner heard popping and rumbling from their gas heater for months. Their gas bill had crept up $30 a month and hot water recovery was slow. The unit was 8 years old.
We flushed the tank, replaced the anode rod, and checked the burner. The popping stopped, recovery time dropped from 45 minutes to 25, and their next gas bill was back to normal. Cost was $260.
Most water heater failures fall into a handful of categories. Here are the ones we see most often and how we handle them.
Ask a pro →We test the pilot assembly, thermocouple, heating elements, and breakers to find the exact failure. Most no-hot-water calls are fixed in under two hours with parts we carry on the truck. You get hot water back the same day.
We trace the leak to its source. If it is a fitting, T&P valve, or drain valve, we repair it on the spot. If the tank liner itself has failed, we tell you straight and quote a replacement so you can decide.
We pull the anode rod and inspect it. If there is still tank life left, we replace the rod and flush the tank. If corrosion has gone too far, we walk you through replacement options before the tank lets go on its own.
We flush the tank to clear the sediment, inspect the element or burner for damage, and check the anode rod while we are in there. A $150 to $250 flush can add years to your heater's life.
$150 - $850 depending on scope
We use flat-rate pricing, which means you know the cost before we start. Typical 2026 water heater repair services Decatur pricing runs $180 to $450 for most jobs. A heating element replacement is $180 to $320. A thermocouple or pilot assembly is $150 to $250. A T&P valve or expansion tank is $200 to $400. If the tank itself has failed, repair does not make sense and we will quote a replacement instead. No hourly billing, no surprise charges, no pressure.
A $250 repair on a 6-year-old heater is a smart investment. A $400 repair on a 15-year-old tank with a failing liner is not. We give you the honest math so you can make the call that saves you money.
A simple thermocouple swap costs less than a full element replacement or a gas valve repair. The more complex the diagnosis and repair, the higher the cost.
Gas repairs often involve more safety checks, including gas pressure testing and flue inspection. Electric repairs are usually faster but may require element and thermostat replacement together.
Common parts like thermocouples and elements are on the truck. Specialty parts for older or less common brands may need to be ordered, which adds a day or two and sometimes a small markup.
A heater in an open garage is easier to work on than one jammed into a closet or attic. Tight access can add labor time and cost.
“Our gas water heater quit on a Friday night and we had family coming Saturday. Called these guys at 7 a.m. and had a tech at the house by 10. Turned out to be the thermocouple. He had the part on the truck, swapped it in 30 minutes, and we had hot water before lunch. Price was exactly what he quoted on the phone.”
Marcus T.Homeowner, Oakhurst
✓ Verified“I noticed water pooling around the base of our heater and thought for sure we needed a new one. The technician checked it out and found the T&P valve was the culprit, not the tank. Fixed it for under $300. He could have easily sold me a replacement and I would not have known the difference. Honest work.”
Sandra K.Homeowner, Winnona Park
✓ Verified“I manage six rental units near the square and use these guys for all my water heater calls. They are fast, they communicate, and they do not leave me guessing on price. Last month they handled an electric element failure in one of my Kirkwood units the same day I called. Tenants were happy, I was happy.”
David R.Property Manager, Downtown Decatur
✓ VerifiedMost leaks come from a failed T&P valve, a loose inlet or outlet fitting, or a cracked tank liner. If the leak is at the top, it is usually a fitting you can fix for $150 to $300. If water is coming from the bottom of the tank itself, the liner has failed and replacement is the only real option. We diagnose it on-site in about 20 minutes and tell you straight which one you have.
Typical 2026 pricing runs $180 to $450 for most repairs. A heating element swap is $180 to $320. A thermocouple or pilot assembly replacement is $150 to $250. A T&P valve or expansion tank runs $200 to $400. If the tank itself is cracked, repair does not make sense and we will quote a replacement instead. You get the exact price before we start.
Yes. We stock common parts on every truck and run same-day service seven days a week. Call before early afternoon and we can usually have a technician at your door within a few hours. Emergency calls for active leaks or no hot water in a full house get priority dispatch. Most same-day repairs are finished in under two hours once we arrive.
If your tank is under 10 years old and the failure is a single component like an element, thermocouple, or valve, repair is almost always the right call. If the tank is 12 years or older, leaking from the bottom, or has rusty water throughout, replacement saves you money long-term. We give you both numbers and let you decide without pressure.
Cold showers end today. Call us and we will diagnose the problem, give you a flat-rate price, and get your hot water back on. Licensed, insured, and warrantied. Same-day service across Decatur and DeKalb County.
Schedule Service (831) 293-1204 →Call us anytime, day or night. Our dispatch line is open 24/7 for emergencies, and our office is staffed Monday through Friday from 8 a.m. to 6 p.m. for scheduling and questions. We serve all of Decatur, Georgia and the surrounding DeKalb County area. If you have a leak, a clog, or no hot water, call now and we will get a plumber headed your way.